IICL Dry Van Practice Exam

These questions are part of the practice quiz. Start practicing

• Why is it important to enforce the correct temperature during straightening?
• Which factor is NOT a consideration for side panel payload capacity?
• What is the minimum length from the floor side to the dowel?
• How do side and end panels contribute to the overall capacity of a dry van?
• Are inserts allowed on the outer profiles of front corner posts?
• What is the standard measurement for upward deformation of the gooseneck bolster?
• What is the minimum distance required between two dowels?
• For bottom side rail outward deformation, what is the maximum condition to adhere to?
• What are the dimensions for tube type top side rails?
• What does IMDG CODE stand for?
• How should the inward deformation of a door be measured?
• What is a critical consideration when installing doors, particularly regarding gaskets?
• What is the role of the side panels in terms of payload capacity?
• If the height difference exceeds 5mm on the floor panel above the forklift pocket, what action should be taken?
• What substrate and cleaning agent should be used when dealing with traupalin patches?
• For the upward deformation of the forklift pocket top plate, where should the measurement be taken from?
• In terms of installation, why is the distance between dowels important?
• What is the minimum distance an insert must maintain from a corner fitting?
• Which type of hammers are not permitted during straightening?
• What measurement is used for the downward deformation of the gooseneck tunnel plate?
• For corner posts, what is one of the main structural requirements regarding inserts?
• What is the limitation for bottom side rail downward deformation with respect to the corner fitting?
• For ventilation systems, what is the standard depth measure?
• What is the measurement reference for the upward deformation of the gooseneck bolster?
• What is the thickness of reinforcement plates under door hardware?
• How much downward deformation is acceptable for the inside of the crossmember on the lower flange?
• What does ISO stand for in standardization?
• What is the necessary clearance required between the door opening to install a gasket?
• What is the measurement for the sideways deformation of the forklift pocket web?
• What is the minimum thickness required for the header extension plate and corner protection plate?
• What is the maximum distance from the formed edge for corner post inserts?
• What is the purpose of using spacers when measuring side rails and sills?
• What is the minimum yield point for welding wire as specified?
• What is the minimum number of screws required for wood sections over 150mm wide?
• What is the clearance between roof components and the top surface of the corner fitting?
• What is the minimum number of crossmembers required under flooring?
• What is the maximum deformation for corner post side face?
• Which materials are recommended for sealing in construction?
• Which of the following practices is not allowed in top rails?
• What is the key aspect for bottom side rail outward deformation measurement?
• What is the acceptable measurement for upward deformation from the inside of the crossmember on web top corners?
• Which aspect is critical for the structural integrity of corner posts?
• What is the maximum number of sections allowed in corner posts?
• When replacing an open type bottom end rail, how many gussets are required on front sills?
• What is the recommended distance between corner post inserts?
• What is the meaning of EIR in logistics?
• For measuring the crossmember/outrigger web sideways deformation, which area should be referenced?
• When a corner post insert extends to corner fittings, what is the minimum distance required?
• What is the maximum length of an insert in adjacent crossmembers?
• How much should patches overlap components when welding?
• When patching a door gasket, how much material should be replaced around the damaged area?
• When assessing deformation, what is the critical distance measured from the bottom side rail for forklift pocket downward deformation?
• What is the maximum length allowed for gooseneck tunnel longitudinal inserts?
• What is the required thickness of TIR cords?
• What is the maximum allowable deformation for a roof panel outward on tube type top rails?
• What is the minimum clearance required between the roof and the top surface of corner fittings?
• Why might one need to modify the locking bar anti-rack rings?
• When assessing payload distribution, which components are considered?
• What material is used for hinge pins?
• How should front panel inward deformation be measured?
• What is the recommended bevel angle when repairing a frame component?
• What is the minimum insert size for J-bars?
• How should the upward deformation of the forklift pocket flange be measured?
• What is not allowed in forklift pockets?
• What is the measurement for side panel inward deformation?
• Are sections allowed on the inner profiles of front corner posts?
• What is the maximum diameter of pinholes that can be repaired using epoxy compounds in traupalins?
• What is the repair threshold for crossmember flange floor separation?
• Which of the following actions is prohibited in flat-bar top rails?
• What is the maximum height difference allowed for the floor panel on top of the forklift pocket?
• What is the minimum shank dimension required for flooring screws?
• How thick should forklift pocket straps be?
• What is the strength of the welding wire required for high-performance applications?
• What is the recommended depth for ventilators?
• Which of the following materials is NOT allowed for floor sealant?
• When measuring bottom side rail web inward deformation, what reference point should be used?
• What is the minimum length and width required for a corner post insert?
• For wide ventilators, how many holes and what diameter should they have?
• What is the minimum distance required between the rail and the roof bow insert?
• When removing multiple roof bows, how often should bows be removed from a 20' trailer?
• What distinguishes tube type top side rails from flat bar top rails?
• How many bows are needed for a 20' dry van?
• What is the function of dowels in construction?
• What is the preferred material for dowels in construction?
• What additional step is required when cutting traupalins for sections?
• How is the roof panel outward deformation measured on flat bar type top side rails?
• What is the maximum allowable deformation for corner protection plates or header extension plates?
• What does IMO stand for in maritime context?
• What is the maximum clearance allowed in inserts during installation?
• When installing a patch, how much should a panel be ground around the edges?
• Which standard reflects the minimum requirement for abrasive cleaning?
• Why is the choice of hardwood for dowels significant?
• What is the minimum crusher bead required for ship-lapped planks?
• Are sections allowed on the outer profiles of rear corner posts?
• What is the maximum diameter of a dowel that can be used for repair in flooring?
• When measuring the downward deformation of the gooseneck tunnel, what reference point is used?
• What is a typical feature expected from top rails in a dry van?
• What is the measurement requirement for door sill web inward deformation?
• What does rear sill downward deformation need to ensure regarding lower surfaces?
• What is the maximum allowed inward deformation for top side rail?
• What is the maximum allowable length and width of a crack?
• What material is defined as Corrosive Resistant High Strength Low Alloy Steel under code G3125?
• If damage extends to the locking bar anti-rack rings, how much should be cut from it?
• What material is specified for floor sealant?
• Which type of welding rod is recommended to avoid hydrogen embrittlement?
• What percentage of payload can side panels withhold?
• Which welding rod type is utilized specifically to prevent hydrogen issues?
• What is the maximum allowable measurement for top side rail outward deformation when using a spacer?
• What is the maximum temperature allowed for straightening during welding?
• Why is a clearance of 6mm significant in design considerations?
• What is a significant restriction regarding patching in rails?
• What is the measurement for corner post end face outward deformation?
• What tool is essential for rolling traupalin patches to get the required pattern?
• Are inserts permitted on the inner profiles of rear corner posts?
• Are sections allowed on the outer profiles of front corner posts?
• In wide ventilators, how many fasteners are typically used?
• What upward camber is needed for a flat panel roof?
• When removing multiple roof bows from a 40' trailer, how often should bows be removed?
• To what depth should flooring screws be counter sunk?
• What is the minimum distance required between an insert and corner fittings?
• How many skip welds and adhesive are needed to attach roof bows?
• How is rear sill outward deformation measured?
• What height limitation is placed on front corner post inserts?
• What is the maximum width limitation for gooseneck tunnel inserts?
• Are inserts allowed on the inner profiles of rear corner posts?
• What measurement condition applies to front sill outward deformation when a spacer is used?
• What type of screws are recommended for flooring in dry vans?
• Are inserts permitted on the outer profiles of rear corner posts?
• How should downward deformation of the gooseneck bolster be measured?
• What is the required thickness for roof panel inserts and patches?
• What is the minimum distance from a rail insert/section to a corner fitting on a side rail?
• For narrow ventilators, how many holes and what diameter must they have?
• What is the material used to bond gaskets?
• What technique can be used to control crack propagation effectively?
• What does a 5mm spacer indicate regarding top side rail upward deformation?
• What is the overlap measurement for patches?
• Are full profile sections allowed on corner posts?
• For top side rail inward deformation, where should the measurement be taken from?
• How should dissimilar materials be addressed to prevent electrolysis?
• Which type of deformation allows the use of a 5mm spacer at the corner fitting for measurement?
• Why is it important to regulate insert sizes and spacing in rails?
• What is the consequence of inadequate clearance between roof components and corner fittings?
• What is the measurement for front panel outward deformation?
• What is the maximum allowed length for insert and section in rails?
• What is a critical property of the adhesive materials used in traupalin patching?
• What is the reference point for measuring outward deformation in corner posts?
• What steps should be taken after applying a traupalin patch?
• Which type of primer should be used on interior panels?
• What is the recommended cut for the vertical face of the door header when removing rain gutters?
• In the context of dry vans, why is the dimension of top side rails important?
• Which aspect is critical for the structural integrity of the top rails?
• What is the recommended method for testing downward deformation in the gooseneck tunnel plate?
• What is the vertical limit for horizontal components during welding?
• What is the maximum moisture level of wood during installation?
• How is corner post side face outward deformation measured?
• In how many adjacent crossmembers can only one insert terminate?
• What is required to measure upward deformation on crossmember web top corners?
• Is it permitted to have multiple inserts on the same horizontal line in corner posts?
• How should outward deformation of a side panel be measured?
• When measuring sideways deformation of the gooseneck bolster web, what area should be used?
• How is the sideways deformation of the gooseneck tunnel plate measured?
• What is the limitation regarding corner post insert formed edges?
• What is the standard thickness for flat bar top rails?
• Which type of measurement is used for surface deformation in dry vans?
• What percentage of payload can end panels withhold?
• Are inserts permitted on the inner profiles of front corner posts?
• What is the maximum allowable gap between plywood floor boards?
• What should be done if door inward deformation exceeds the acceptable measurement?
• What should be ensured about front sill downward deformation relative to the corner fitting?
• What is critical about the overlap measurement while patching?
• What is the minimum length required between the floor end and the screw for a dowel?
• What is the minimum standard for abrasive cleaning on the underside of surfaces?
• How many screws are required for wood sections that are 150mm or less wide?
• What are the specifications for center support thickness and width?
• The ideal gasket patch replacement distance from the damage area is...
• What is the measurement for corner post inward deformation?
• What is the primary material requirement for header extension plate or corner protection plate inserts?
• Which material is known for bonding gaskets?
• What is the recommended measurement for detecting downward deformation in the goose neck tunnel?
• What is the correct measurement for roof panel inward deformation?
• What is the maximum corner post insert width relative to its cross section?
• When repairing components attached to corner fittings, what is the appropriate bevel angle?
• What is the minimum distance required between inserts and sections in rails?
• What is the maximum gap allowed for crossmember flange floor separation before a repair is required?
• What is the minimum yield point of Corten steel?
• What is the minimum distance from a rail insert/section to a corner fitting on an end rail?
• What method is used to prevent the spread of cracks in welded components?
• What is the correct method for installing overlapping crossmember web patches?
• What material is commonly used for door gaskets?
• How much should forklift pocket straps protrude into the forklift pocket?